抗菌防霉整理剂

HOLPOSON® Captain AM

HOLPOSON® Captain AM 是一种具有抗菌、防霉和防螨多重作用的抗菌防霉整理剂，适用于大多数的纺织纤维，

如：棉、毛、涤棉、锦纶、腈纶、粘胶、涤纶等天然、合成纤维及混纺织物。即可应用在针织物、梭织物、运动装、工作服、

无菌行业服装 、家纺产品、装饰用布等纺织品。

物化性能

外 观：乳白色至微黄的分散液

离 子 型：弱阴离子

主要成份：有机季铵盐

溶 解 性：分散溶于水

使用方法

首先称取抗菌防霉剂HOLPOSON® Captain AM，搅拌同时加水，然后稀释到所需要的浓度，按照如下工艺进行生产：

1．浸轧法

HOLPOSON® Captain AM     15-20g/L

交联剂HOLPOSON®HFM      10g/L

柔软剂HOLPOSON®SOFT      5g/L

轧液率 60-70%

工艺：110℃烘干  然后150℃定型 60~90秒

2. 浸渍法

HOLPOSON® Captain AM       1-2%

交联剂HOLPOSON®HFM       1%

工艺：浴比 1:10

处理条件：20℃浸渍处理20~ 30分钟，脱水（带液率60~100%），烘干。

3. 喷洒法

配成50~60g/L(根据实际情况配置相应要求的浓度)的溶液， 喷洒在需处理的产品表面， 自然晾晒或烘干。

注意事项

1.化料时用冷水或温水（约30 ~40℃），可保证产品良好的加工稳定性和抗菌效果.

2.但如果使用一部分助剂如纤维消光剂，整理效果会有所下降；或织物的组织结构过于疏松对抗菌检测也有影响。

3.为了整理效果，我们建议预先试验。整理效果主要取决于织物类型。

贮存

存放在阴凉干燥通风的地方，该产品的贮存期限至少为1年。开封后尽快用完。如果没有用完，

请盖紧防止产品受潮或混入异物。

Antibacterial and Mildew-Proof

Finishing Agent

HOLPOSON® Captain AM

HOLPOSON® Captain AM is an anti-bacterial, mildew-proof and anti-mite finishing agent with multiple functions. It is suitable for the majority of textile fibers, such as: cotton, wool, polyester-cotton, nylon, acrylic, viscose, polyester.etc and blended fabrics. So it can be used in knitted fabrics, woven fabrics, sportswear, work clothes, aseptic industry clothing, home textile products, decorative fabrics and other textiles.

Physical & chemical properties:

Appearance: Milky white to yellowish dispersion liquid

Ionicity: Weak anionic

Main contents: Organic quaternary ammonium salt

Solubility:         Dispersable and soluble in water

Usage:

First, weigh and take the HOLPOSON® Captain AM, stir it while adding water, then dilute it to the required concentration, and carry out the production according to the following process:

1. Padding method

HOLPOSON®Captain AM: 15-20g/L

Crosslinker HOLPOSON®HFM: 10g/L

Softener HOLPOSON®SOFT: 5g/L

Liquid retention rate: 60-70%

Process: Drying at 110 ℃ and heat setting at 150 ℃ for 60-90 seconds

2. Impregnation method

HOLPOSON®Captain AM: 1-2%

Crosslinker HOLPOSON® HFM: 1%

Process: Bath ratio: 1:10

Treatment condition: Impregnation at 20 ℃ for 20-30 minutes, dehydration (with liquid rate of 60-100%), drying.

3. Spraying method

Prepare a solution of 50-60g/L (prepare the required concentration according to the actual situation), spray it on the surface of the material to be treated, and dry it naturally or dry it with heat.

Attentions:

1. Dissolving the product with cold water or warm water (about 30 ~ 40 ℃) can ensure good processing stability and antibacterial effect of the product

2. If some auxiliaries such as fiber matting agent are used, the finishing effect will be reduced. Or if the structure of the fabric is too loose, the antibacterial test result will also be affected.

3. In order to guarantee the overall the effect, we suggest to test in advance. The overall effect mainly depends on the fabric type.

Storage:

Store in a cool, dry and ventilated place. The storage time is 1 year minimum. Use up as soon as possible after opening. If it is not used up, please cover it tightly to prevent the product from moisture or foreign matters.